No, we don’t offer Otabind, Swiss or open spine sewn binding, sorry.
If your book needs to open flatter, the closest we get is section sewing, on a hardback or a paperback. And if you have 72 pages or fewer, a stapled booklet opens completely flat.
What exposed spine binding actually is
Exposed spine is a family of bindings where the back of the book block is left on show, so the pages can open right out without a cover pulling against them. You’ll hear three names most often:
They look gorgeous on sketchbooks, cookbooks and art books. They’re also specialist bindings, and they aren’t among the three styles we print and bind.
Why people ask for it
Almost always for one reason: the book has to stay open while someone works in it. Sketchbooks, drawing prompt books, music, recipe books and manuals all fall into this camp.
A typical request reads like this: an A5 book of 64 pages on a toothy 150gsm uncoated paper that takes ink and charcoal, which “needs to open flat without wire”. That’s a brilliant brief, and it’s exactly what section sewing was made for.
Nothing we bind will sit open at a full 180° by itself the way an Otabind can.
Section sewing gets you most of the way there, and it is far tougher than glue when a book is pressed flat again and again.
Section sewn hardbacks: tough, and they open flatter
Instead of gluing single pages together, we fold the inside pages into sections and stitch each one with thread before the book is bound. Because every page is held by the fold rather than by a strip of glue, the pages flex where they meet the spine.
That flex is what lets a section sewn book be pressed down and opened again for years without the pages working loose.
A section sewn book can be pressed much flatter than a glued one. Pushing it all the way back to 180°, over and over, still risks cracking the spine.
Treat it like a good sketchbook: open it wide, press it gently, and let it do the rest.
Section sewing is available on hardbacks in any quantity, and you can add head and tail bands once the page block is at least 10mm thick. Our section sewn answer covers the basics.
Section sewn paperbacks: the same stitching, a softer cover
You don’t need boards to benefit from thread. A section sewn paperback has its sections stitched exactly the same way, then a printed softback cover is fixed around them with PUR glue. You get the friendly flex of sewing with the lighter weight and lower cost of a softback. The minimum is 32 inside pages, which we sew as four sections of 8 or a pair of 16s.
For a drawing book with mostly blank pages on a heavier uncoated paper, this is usually our first suggestion. It feels like a proper sketchbook in the hand, and it is happy to be opened wide on a desk.
Stapled booklets: the only binding that opens truly flat
If your book is 72 pages or fewer, don’t overlook staples. A stapled booklet has no spine to fight, so every spread opens completely flat, edge to edge.
The catch is bounce. Past about 40 pages, and especially on heavier paper, the pages curl at the centre and push the booklet open. A thick stack of 150gsm drawing paper will feel that more than a slim zine. Our binding styles guide explains bounce in detail.
Which one suits your book?
| Stapled booklet | Section sewn paperback | Section sewn hardback | |
|---|---|---|---|
| Opens flat? | Completely | Far flatter than glued | Far flatter than glued |
| Page count | 8 to 72, a multiple of 4 | 32 inside pages minimum | 28 inside pages minimum |
| Spine | Stapled edge | Square and printable | Square and printable, from 9mm |
| Best for | Slim sketchbooks, zines, workbooks | Sketchbooks, drawing prompt books, art books | Keepsake sketchbooks, cookbooks, gift editions |
| Budget | £ | ££ | £££ |
Design for the gutter, whichever you choose
Apart from stapling, every binding loses a little of each page into the curve of the spine. A few small habits keep your work safe:
Fix: Keep text 6 to 8mm from the spine side of each page, so nothing important hides in the valley.
Fix: On a paperback the cover grips them, so give those two pages 10 to 12mm of clear space at the spine.
Fix: Sewing opens flatter, but not perfectly flat. Shift faces and headlines away from the centre of a spread.
The gutter answer in our Knowledge Base has the full measurements.
Watch our three bindings, then see sewing up close
Two short films showing section sewing on real books we’ve printed:
The questions we answer every day
Do you offer Otabind or Swiss binding?
No, sorry. Neither is on our list. For the flattest possible opening, ask us about a section sewn paperback or hardback, or staples for a slimmer book.
Can you leave the stitching visible on the spine?
Not as a finished binding. On our section sewn books the thread is always there, doing its job, but it sits hidden under the cover.
Will a section sewn book open out to 180°?
It opens a great deal wider than glue allows and takes being pressed down far more happily. We still wouldn’t push it all the way to 180°, because that risks cracking the spine.
Can you section sew a small run of demo copies?
On hardbacks, yes: we section sew on any quantity, so a handful of test copies is fine. Section sewn paperbacks start at 32 inside pages, enough for four 8 page sections or two 16s.
Does section sewing cost more?
Yes. Each section is stitched first, so it costs more than a glued binding. For a sketchbook or a book that will be opened again and again, it’s money well spent.
Is a stapled booklet strong enough for a sketchbook?
For a slimmer book, absolutely. Staples open completely flat and handle up to 72 pages. Heavy stock in a thick booklet tends to spring open, so a sewn binding suits chunkier books better.
Tell us how your book will be used. We’ll find the flattest way to bind it.
A real person checks your file by hand, for free. There’s no minimum, so a few demo copies are very welcome.